Tushar Jadhav Blog

1) What is Raid and Raid Level

RAID can allow for better storage performance and higher availability, and there are many different RAID types.

RAID (originally redundant array of inexpensive disks; now commonly redundant array of independent disks) is a data storage virtualization technology that combines multiple disk drive components into a logical unit for the purposes of data redundancy or performance improvement.

Raid contains groups or sets or Arrays. A combine of drivers make a group of disks to form a RAID Array or RAID set. It can be a minimum of 2 number of disk connected to a raid controller and make a logical volume or more drives can be in a group. Only one Raid level can be applied in a group of disks. Raid are used when we need excellent performance. According to our selected raid level, performance will differ. Saving our data by fault tolerance & high availability.

In RAID we have different RAID levels
1. Level 0 - striped disk array without fault tolerance
2. Level 1 - mirroring and duplexing
3. Level 2 - error-correcting coding
4. Level 3 - bit-interleaved parity
5. Level 4 - dedicated parity drive
6. Level 5 - block interleaved distributed parity
7. Level 6 - independent data disks with double parity
8. Level 10 - a stripe of mirrors

2) Difference Between Raid 5 and Raid 1 + 0

RAID Level 5: Block-level striping with distributed parity. Each entire data block is written on a data disk; parity for blocks in the same rank is generated on Writes, recorded in a distributed location and checked on Reads. Requires minimum 3 disks to implement

Highest Read data transaction rate
Medium Write data transaction rate
Low ratio of ECC (Parity) disks to data disks means high efficiency
Good aggregate transfer rate

RAID Level 0: It’s just stripping. RAID Level 0 requires a minimum of 2 drives to implement.

RAID 0 implements a striped disk array, the data is broken down into blocks and each block is written to a separate disk drive
I/O performance is greatly improved by spreading the I/O load across many channels and drives
Best performance is achieved when data is striped across multiple controllers with only one drive per controller
No parity calculation overhead is involved
Very simple design
Easy to implement

RAID Level 1: For Highest performance, the controller must be able to perform two concurrent separate Reads per mirrored pair or two duplicate Writes per mirrored pair. Raid level 1 requires a minimum of 2 drives to implement.

One Write or two Reads possible per mirrored pair
Twice the Read transaction rate of single disks, same Write transaction rate as single disks
100% redundancy of data means no rebuild is necessary in case of a disk failure, just a copy to the replacement disk
Transfer rate per block is equal to that of a single disk
Under certain circumstances, RAID 1 can sustain multiple simultaneous drive failures
Simplest RAID storage subsystem design

3) what is differene between Hardware Raid and Software Raid.

Implementing the RAID will be two types 1.Software RAID and 2.Hardware RAID
Let’s see the difference between those

SOFTWARE RAID	HARDWARE RAID
1. It will use computer system CPU	1. It will use its own CPU
2. Low cost compare to H/W RAID	2.More cost compare to S/W RAID
3. It has data integrity issues due to system crashes	3.No data integrity issues
4. No write-back cache	4.It is capable of write-back cache
5. Limited operating system migrations	5.Can be migrated to any OS type
6. Unprotected at boot (cannot manage or protect data at boot):Drive failure or corrupted data during boot and before the RAID software become active leads to an inoperable system	6. Protected at boot: No negative impact on data availability when boot drive has medium errors or fails completely
7. Performance issues will be there	7.No performance issues compare to S/W RAID

Software RAID have low performance, because of consuming resource from hosts. Raid software need to load for read data from software raid volumes. Before loading raid software, OS need to get boot to load the raid software. No need of Physical hardware in software raids. Zero cost investment.

Hardware RAID have high performance. They are dedicated RAID Controller which is Physically built using PCI express cards. It won’t use the host resource. They have NVRAM for cache to read and write. Stores cache while rebuild even if there is power-failure, it will store the cache using battery power backups. Very costly investments needed for a large scale.

4) Why FTP work on 21 port?

Purpose:
Reserved TCP port used by File Transfer Protocol (FTP) to initiate and control connections to FTP servers.

Description:
To establish an FTP session, clients initiate a connection to an FTP server that listens on TCP port 21 by default. FTP servers respond with messages that prompt the client for FTP login credentials (username and password). FTP servers do not, however, send files from port number 21.

Instead, the FTP protocol allows for a second connection to be established for data transfer after the control connection is established. Note that only FTP servers use port 21, not FTP clients.

5) When NFS start by default which 4 services port start ?

NFS –Network File Sharing
NFS PORT ------2049
NFS Run on UDP Protocol
NFS doesn’t ask to username & password
NFS used for Linux to Linux only
NFS fast and good performance

Starting NFS services: ------ok ] Main Services
Starting NFS quotas: -------ok ]
Starting NFS deamon: ------ok ] Child Service
Starting NFS mountd: ------ok ]

exportfs –a ----- re-read the file
exportfs –v ------ Display

(sync) -------- under the bracket “( )” called Permission
*(sync) ------- * means ----sharing to all network

showmount -e 192.168.10.x ------ to check it out share drive is accessible or not

NFS V3 VS NFS V4

Export Management

In NFSv3, client must rely on auxiliary protocol, the mount protocol to request a list of server’s exports and obtain root filehandle of a given export. It is fed into the NFS protocol proper once the root filehandle is obtained.
In NFSv4 uses the virtual file system to present the server’s export and associated root filehandles to the client.
NFSv4 defines a special operation to retrieve the Root filehandle and the NFS Server presents the appearance to the client that each export is just a directory in the pseudofs
NFSv4 Pseudo File System is supposed to provide maximum flexibility. Exports Path name on servers can be changed transparently to clients.

6) DNS configuration file name

/etc/named.conf

DNS Package name : bind*

DNS Port : 53

7) XFS File system and difference between ext4 and XFS file system.

Ext4

Ext4 stands for fourth extended file system.
It was introduced in 2008.
Starting from Linux Kernel 2.6.19 ext4 was available.
Supports huge individual file size and overall file system size.
Maximum individual file size can be from 16 GB to 16 TB
Overall maximum ext4 file system size is 1 EB (exabyte). 1 EB = 1024 PB (petabyte). 1 PB = 1024 TB (terabyte).
Directory can contain a maximum of 64,000 subdirectories (as opposed to 32,000 in ext3)
You can also mount an existing ext3 fs as ext4 fs (without having to upgrade it).
Several other new features are introduced in ext4: multiblock allocation, delayed allocation, journal checksum. fast fsck, etc. All you need to know is that these new features have improved the performance and reliability of the filesystem when compared to ext3.
In ext4, you also have the option of turning the journaling feature “off”.

XFS File System

The XFS file system is an extension of the extent file system.
The XFS is a high-performance 64-bit journaling file system.
The support of the XFS was merged into Linux kernel in around 2002 and In 2009 Red Hat Enterprise Linux version 5.4 usage of the XFS file system.
XFS supports maximum file system size of 8 exbibytes for the 64-bit file system.
There is some comparison of XFS file system is XFS file system can’t be shrunk and poor performance with deletions of the large numbers of files.
Now, the RHEL 7.0 uses XFS as the default filesystem.

Common Commands for ext3 and ext4 Compared to XFS

Task	ext3/4	XFS
Create a file system	mkfs.ext4 or mkfs.ext3	mkfs.xfs
File system check	e2fsck	xfs_repair
Resizing a file system	resize2fs	xfs_growfs
Save an image of a file system	e2image	xfs_metadump and xfs_mdrestore
Label or tune a file system	tune2fs	xfs_admin
Backup a file system	dump and restore	xfsdump and xfsrestore

8) Boot Process.

The following are the 6 high level stages of a typical Linux boot process.

9) If Server Load Increase What is Troubleshooting steps you will follow.

High server load – What is it really?

A server functions with a limited set of resources. For eg., an average server these days will have 8 GB RAM, 4 processors, 75 IOPS SATA II hard disks, and 1 Gigabit NIC cards.

Now, let’s assume one user decided to backup their account. If that process occupies 7.5 GB of RAM, other users or services in the system have to wait for that process to get over. The longer the backup takes, the longer the wait queue. The “length” of the queue is represented as server load. So, a server running at load avg. 20, will have a longer wait queue than a server at load avg. 10.

The key to quickly trace a load spike is to go from what you know to what you don’t.

When you get a high load notification, there’s only one thing you know. That is – there’s some server resource (RAM, CPU, I/O, etc.) that’s being abused.

So, the first step is to find out which resource is being abused. The next step is to find out which service is using that resource. It could be the web server, database server, mail server, or some other service. Once you have the service, you can then find out which user in that service is actually abusing the server.

Find the over-loaded resource
Find the service hogging that resource
Find the virtual host over-using that service

10) Command SAR

SAR System Monitoring

11) AWS Instances , VPC, AMI

12) How DHCP works (DORA Process)

DHCP stands for Dynamic Host Configuration Protocol.

The DORA process in DHCP works as folows.

D ----------> Discover
O ----------> Offer
R ----------> Request
A ----------> Acknowledgement

DHCP (D)iscover | DHCP (O)ffer | DHCP (R)equest | DHCP (A)ck

D – D in the term DORA stands for the DHCP Discover packet. The DHCP Discover packet
is broadcasted by the DHCP client computer in order to find the available DHCP server(s) in the network. Since the DHCP client computer sends the DHCP Discover packet as a broadcast, all the
DHCP servers that are present in the network receive the packet and respond accordingly.

O – O in the term DORA stands for the DHCP Offer packet. The DHCP Offer is a unicast packet that is sent by the DHCP server who receives the DHCP Discover packet from the DHCP client computer. The DHCP Offer packet contains the available IP address that the DHCP server offers to the client computer.

R – R in the term DORA stands for the DHCP Request packet. The DHCP Request is again a unicast packet sent by the DHCP client computer to the DHCP server who had sent the DHCP Offer packet to the client computer. With the help of the DHCP Request packet, the DHCP client computer requests the DHCP server to assign the offered IP address to it.

A – A in the term DORA stands for the DHCP Acknowledge packet. The DHCP Acknowledge is a unicast packet sent by the DHCP server to the DHCP client computer acknowledging the assignment of the offered IP address for a specific lease time.

1) Client makes a UDP Broadcast to the server about the DHCP discovery.

2) DHCP offers to the client.
3) In response to the offer Client requests the server.
4)Server responds all the Ip Add/mask/gty/dns/wins info along with the acknowledgement packet.

13) Subversion

14) LVM Questions

15) Linux basic Interview Question - 1

16) Linux basic Interview Question - 2

17) Linux basic Interview Question - 3

18) Linux Apache Interview Question -1

19) Linux Apache Interview Question -2

20) Linux DNS Interview Question -1

21) Linux Nagios Interview Question -1

22) Linux Interview Question - Part 1

23) Linux Interview Question - Part 2

24) Linux Interview Question - Part 3

25) Linux Interview Question - Part 4

26) Linux Interview Question - Part 5

27) Linux Interview Question - Part 6

28) AWS Interview Questions

29) General Linux Interview Questions

30) Apache Web server Interview Questions

To set up a LAMP server on a fresh VPS/Dedicated server running CentOS 5.0 with atleast 256mb of RAM. ...
Install Apache. ...
Install MySQL Database Server. ...
Changing MySQL Root Password. ...
To Create A New MySQL User. ...
Install PHP5 Scripting Language. ...
To Test If PHP Is Working Or Not: ...
Install phpMyAdmin.

________________________________________

1) Install Apache

yum install httpd httpd-devel
/etc/init.d/httpd start

2) Install MySQL Database Server

yum install mysql mysql-server mysql-devel

First start the mysql daemon, then type mysql:

/etc/init.d/mysqld start
2 Way to Change MySQL Root Password

By default the root password is empty for the mysql database. It is a good idea to change the mysql root password to a new one from a security point of view.

1) mysql_secure_installation

2) mysql
mysql> USE mysql;
mysql> UPDATE user SET Password=PASSWORD('newpassword') WHERE user='root';

mysql> FLUSH PRIVILEGES;

Once done, check by logging in:

mysql -u root -p

Enter Password: <your new password>

To Create A New MySQL User

To create a new mysql user 'harry' with 'all privileges' on the database 'demo':
mysql > create database demo
mysql >GRANT ALL PRIVILEGES ON demo.* TO 'harry'@'localhost' IDENTIFIED BY 'harry' WITH GRANT OPTION;
mysql> UPDATE user SET Password=PASSWORD('harry') WHERE user='harry';

That's it! MySQL is ready! Don't forget to remember the root password as we might be using it with phpmyadmin.
3) Install PHP5 Scripting Language

Installing PHP5 with the necessary modules is so easy and can be configured for both the Apache and mysql environment.
yum install php php-mysql php-common php-gd php-mbstring php-mcrypt php-devel php-xml

Don't forget to install php-gd (gd library). It is very important if we plan to run captcha scripts on our server and so as other which are dependent on mysql and other functions.
Restart Apache to load php.

/etc/init.d/httpd restart

To Test If PHP Is Working Or Not:

Create a file named /var/www/html/test.php with the following phpinfo() function inside php quotes.

// test.php
<?php
phpinfo();
?>

Edit /etc/httpd/conf/httpd.conf

<VirtualHost *:80>
ServerAdmin webmaster@dummy-host.example.com
DocumentRoot /var/www/html/test.php
ServerName funny.com
ErrorLog logs/dummy-host.example.com-error_log
CustomLog logs/dummy-host.example.com-access_log common
</VirtualHost>

Then point your browser to http://ip.address/test.php.

4) Install phpMyAdmin

yum install phpmyadmin

Point your browser to: http://ip.address/phpmyadmin.

Edit the /etc/httpd/conf.d/phpmyadmin.conf

# phpMyAdmin - Web based MySQL browser written in php
#
# Allows only localhost by default
#
# But allowing phpMyAdmin to anyone other than localhost should be considered
# dangerous unless properly secured by SSL

Alias /phpMyAdmin /usr/share/phpMyAdmin
Alias /phpmyadmin /usr/share/phpMyAdmin

<Directory /usr/share/phpMyAdmin/>
AddDefaultCharset UTF-8

<IfModule mod_authz_core.c>
# Apache 2.4
<RequireAny>
Require all granted
Require ip ::1
</RequireAny>
</IfModule>
# <IfModule !mod_authz_core.c>
# Apache 2.2
# Order Deny,Allow
# Deny from All
# Allow from 127.0.0.1
# Allow from ::1
# </IfModule>
</Directory>

<Directory /usr/share/phpMyAdmin/setup/>
<IfModule mod_authz_core.c>
# Apache 2.4
# <RequireAny>
# Require ip 127.0.0.1
# Require ip ::1
# </RequireAny>
</IfModule>
<IfModule !mod_authz_core.c>
# Apache 2.2
Order Deny,Allow
# Deny from All
Allow from All
Allow from ::1
</IfModule>
</Directory>

# These directories do not require access over HTTP - taken from the original
# phpMyAdmin upstream tarball
#
<Directory /usr/share/phpMyAdmin/libraries/>
Order Deny,Allow
Deny from All
Allow from None
</Directory>

<Directory /usr/share/phpMyAdmin/setup/lib/>
Order Deny,Allow
Deny from All
Allow from None
</Directory>

<Directory /usr/share/phpMyAdmin/setup/frames/>
Order Deny,Allow
Deny from All
Allow from None
</Directory>

# This configuration prevents mod_security at phpMyAdmin directories from
# filtering SQL etc. This may break your mod_security implementation.
#
#<IfModule mod_security.c>
# <Directory /usr/share/phpMyAdmin/>
# SecRuleInheritance Off
# </Directory>
#</IfModule>

Point your browser to: http://ip.address/phpmyadmin.

User Name : root

Password : newpassword

chkconfig httpd on
chkconfig mysqld on

Tushar Jadhav Blog

Friday, January 13, 2017

Linux Interview Question Final

Wednesday, January 11, 2017

LAMP Server Installation

SCM-MANAGER INSTALLATION

Sunday, January 1, 2017

Script for s3 Becket